What is the best way to connect the countertop under the hob? Hob installation

If you need to save space in the kitchen, there is no point in installing a gas stove, which takes up quite a lot of space. Moreover, not everyone uses the oven that comes with it, especially with the advent of a large number of microwave ovens and electric ovens at an affordable price. For the most part, the cooking surface is used directly for cooking. There is no fundamental difference in the installation of gas and electric hobs, only some nuances that will be discussed later in the article.

Necessary tools, materials

To install the panel, you do not need any expensive or outlandish tools or special courses. Everything is quite simple; anyone who is more or less handy with their hands can master the process. During the work you will need:

• roulette;
• a drill with a drill with a diameter of 8 mm or more to drill a couple of holes into which a jigsaw file will fit;
• electric jigsaw (you can cut it by hand, but it will be longer and more tedious);
• sealant;
• special plasticine, self-adhesive sealant or aluminum tape.

IN this list included accessories that will definitely be needed. Also, depending on the type of surface, other materials will be needed, for example, Teflon or tow for winding threads, terminals, and electrical tape for contacts. The main thing is to get involved in the battle, and then it will become clear what else is needed.

Measurements

The easiest way to mark is to carefully trace the contours of the panel directly on the tabletop, ensuring an equal distance from its edges. You can go another way:

• first transfer the contours of the shelf above which it is located to the tabletop;
• find the center of the resulting rectangle, mark it with a cross on the tabletop and make it the middle of the contour under the stove;
• after measuring the dimensions of the slab using a tape measure, give an additional 5 millimeters of allowance on each side to the hole being prepared, the marked cross is the point of intersection of the diagonals and the middle of the hole (it is advisable to verify the accuracy of the markings by drawing the diagonals in the image).

Pruning

To cut with a jigsaw, you need to drill holes in the corners of the intended contour using a drill so that the file fits into them freely. It is enough to make two holes located diagonally relative to each other. Two cuts are made from each hole according to the markings. Most clearly, such cuts are made using a hand router, but not everyone has one, so a jigsaw is a more realistic option. Carefully, according to the markings, at medium speeds, slowly move the jigsaw clearly along the markings, making sure that it does not go to the side. It is highly recommended to try to make several cuts on some unnecessary block.

Important nuance– some advise marking and trimming on the back side of the tabletop. The problem is that the laminate that covers the front side may chip, and the slab will not cover the chip. Therefore, it is easier to mark with a marker on the front side, and drill and saw with the front side up.

Installation and sealing

After the cut has been made, the edges of the slot are treated with silicone or other sealant to protect it from moisture. Along the perimeter of the hole prepared in this way, glue the sealant that is usually included with the plate on the upper side. Then the plate is inserted and aligned along the contour of the hole, after which the fasteners located on the back side are tightened. If the seal protrudes beyond the edges of the surface, carefully cut off the excess with a knife, being careful not to scratch the countertop.

Features of installing gas and electric panels

Important! According to safety regulations when using gas appliances, unauthorized connection of gas appliances, including hobs, is PROHIBITED.

This provision is enshrined in current legislation. The connection is usually carried out by Gorgaz employees for an appropriate fee. You can install the device yourself at your own risk, but you should expect possible sanctions from the organization supplying the gas, up to and including turning it off and sealing the valve. All montages gas equipment must be carried out in agreement with relevant organizations.

If, however, there is a desire to manage things on your own, they act in the following sequence:

• a flexible hose is connected to the gas valve through a squeegee or fitting;
• prepare a hole in the furniture for the hose;
• the presence of jets for the main connection of the stove is checked; if they are not installed, they must be installed;
• the gas supply nut is connected to the stove, and always with an o-ring; the connection angle is usually included in the kit.

Checking for gas leaks is carried out by applying a soap solution to the joints. It should not bubble; if there are bubbles, this indicates a leak, as well as the presence of a characteristic smell of gas.

Installation of an electric hob is carried out strictly according to the diagram given in the instructions. If you have little experience working with electrical appliances, you shouldn’t experiment; it’s better to turn to specialists. If the power supply is connected incorrectly, it is possible that the device will not operate properly or that it, as well as the wiring in the apartment, may fail. The power supply is connected before installing the tiles into the socket prepared in the countertop.

Various models provide options for connecting the wire either to an outlet or directly to an electrical panel. It should be remembered that an electric hob consumes quite a large number of electricity, and ensure that the wiring meets the power requirements.

This step-by-step instruction on how to cut a hole in a countertop made of chipboard or MDF for a hob with your own hands. When you probably need to know how to cut holes in chipboard or MDF countertops if you are installing a sink or cooktop. This task may seem simple, but we can assure you that there are many nuances that need to be taken into account for a good result.

On the one hand, you must carefully follow the contour gas stove using the template or following the instructions on the product. In most cases, there are certain restrictions that you must pay attention to, such as the minimum distance from the stove to the back panel or on both sides, to. Use a large L-shaped square to draw a rectangle on your workbench, otherwise the corners will not be at right angles.

To get an accurate hole, you must use a good saw with the appropriate blade. Therefore, the blade must have teeth oriented downward, otherwise it will split the surface. Drill starting holes along the four corners of the rectangle using a drill or (the hole should be wider than the size of the jigsaw blade).

Work plan for installing the hob into the countertop

Materials:

• table top;
• carpenter's pencil;
• insulating tape.

Tools:

1. Protective gloves, safety glasses;
2. Saw or jigsaw;
3. Tape measure, level, square;
4. C-clamps.

• Wear safety glasses when making cuts.
• Choose a blade with fine teeth.

Deadline

• 10 minutes

When installing a gas stove hob or hob, you must cut holes in the countertop.

Tip: Follow the manufacturer's instructions when cutting a hole in your kitchen countertop if you want to prevent potential problems.

How to cut a hole in a countertop for a hob

Marking guide lines

The first step is to determine the outline of the slab. In most cases, it should contain instructions on how to do this, but there is a technique that only provides recommended hole sizes. Place the hob on top of the cabinets. Leave the recommended distance from the back panel to the front edge of the tabletop.

Draw a median on the countertop and mark the cut lines using the manufacturer's instructions.

Marking the countertop for the hole for the stove

As you can see in the picture, you need an L-square, a tape measure, and a carpenter's pencil to get the job done professionally. Make sure the cut lines are parallel and at right angles. In addition, the rectangle must be symmetrical.

Tip: Check that the rectangle under the kitchen cabinet in which the hood will be built is correctly positioned and there is enough space around it (according to the manufacturer's instructions).

Installing spacers under the countertop

To get an accurate result, you should place several spacers under the tabletop. However, the tabletop must be level.

You should leave about 2 inches of space between the cabinets and the countertop, otherwise the saw blade could damage them.

Making initial holes for drilling

Use a drill with a special bit to create starting holes along the corners. It is very important to line up the bits correctly, otherwise you may drill out of line.

Tip: Make sure you use good equipment for drilling with speed control. Set the drill at low speeds and hold the drill with both hands if you want to have good control above her. Repeat the process for each corner of the rectangle.

Passing the laminated layer

In this image you should notice that the drill bit is going through the top layer. Do not use too much pressure on the drilling equipment, otherwise it may slip out of place.

We remove residues from the process with a vacuum cleaner

Drilling a hole in a countertop with a drill will create a lot of residue, so we recommend that you have someone clean it up as you make the hole.

Tip: Work with great care and attention as it is important to make the holes exactly in the indicated places.

Initial holes for cutting in the tabletop

After drilling the corner pilot holes, you need to make cuts along the guide lines. If you are not experienced in this area, you should cover the cut lines with masking tape. This way you will help prevent the edges from fraying.

Cutting a hole with a jigsaw in a tabletop

To make the cuts, we recommend that you use a jigsaw. Choose a blade with downward-facing teeth. In addition, the blade must have set teeth. If you have not worked with a jigsaw before, we recommend that you secure the tabletop. Make sure the blade follows the cut lines exactly.

Tip: Remove chips that are generated frequently, otherwise they may cover the lines. Set the jigsaw at low speeds.

Finished hole in the countertop for the stove

Last but not least, you need to take care of installing the hob into the countertop yourself. If you followed our tips and read the manufacturer's instructions, the hob should fit into the hole easily. However, if the edges are not completely straight, you can smooth them with silicone or caulk.

Tip: Use sandpaper to smooth the cutting edges.

Installing the hob into the countertop

After this, all you have to do is install the hob into the countertop, connect it and secure it with the screws that should come with it.

Thank you for reading our step by step recommendation How to cut a hole in a countertop and install a hob with your own hands, we recommend that you read other articles. Don't forget to share our projects with your friends using social network widgets.

Have you decided to completely change the interior of your kitchen and make the room more functional, beautiful and modern? It is necessary to approach this process with maximum responsibility and understanding. Replacing the headset is only half the battle. Today it is impossible to imagine a kitchen without modern, high-tech household appliances, which is able to make the housewife’s work easier. Installation hob Only at first glance it seems like a simple matter that anyone can easily handle. The slightest mistake can ruin complex, expensive equipment and nullify your efforts. Therefore, it is best to enlist the support of professionals.

Installing the hob: the first step is marking.

It is necessary to understand that without correct markings it is impossible to install the equipment efficiently and reliably. We can say with 100% certainty that poor-quality markings can negate all your efforts to modernize the premises. It guarantees that all holes made subsequently will exactly correspond to the required parameters and ensure high-quality work. Any countertop costs a lot, so the slightest inaccuracy will certainly become a prerequisite for additional financial investments.

Buying a new countertop, especially if it was made from valuable wood, will result in significant costs. Installation of a hob - the price of services always depends on many factors and requires the involvement of professionals. Often people take the simplest route and trace the panel laid on the countertop with a pencil and make the holes by eye. Professionals never do this. Accurate measurement of all parameters and impeccable marking of each position down to the millimeter will ensure the ideal appearance and reliable operation of the new equipment. The stages of high-quality and correct marking include several steps.

Postpone inner space cabinets on the surface of the table top. To do this, use a marker or soft pencil to draw parallel lines that exactly correspond to the boundaries internal partitions. It should be a perfect rectangle. By connecting the corners, we find the exact center in which the cross is drawn. One line should be parallel to the front and back lines, and the other should be parallel to the side lines. It is best to use a construction square for this.

Having drawn your coordinate system, you need to transfer the dimensions of the embedded panel elements onto it with the utmost care. It is necessary to make holes with a small margin, which will help to accurately center the device. After marking and checking their exact correspondence to the original data, we draw parallel lines, which, after connecting them, will be the hole into which, after cutting, the hob will exactly fit.

It is important! In order for the hole to be perfectly smooth and not extend beyond the edges of the equipment being mounted, you need to mark slowly, using quality tools. You need to cut the hole with an electric jigsaw, which makes it possible to make an even and high-quality cut.

In order for the installation to go perfectly, it is necessary to perform all the work efficiently.

To cut holes of a given size in the tabletop monolith, you can use an electric jigsaw, drill or hand-held milling machine. Our specialists have everything at their disposal necessary equipment and guarantee high quality of work performed.

By the way! In order to cut a mounting hole using a drill, you need to stock up on several drills with a diameter of 8-10 millimeters and, following the contour of the marking, drill as many holes as possible with minimum distance from each other. After this, using the same drill, all the holes are gradually connected. The main thing is to work along the internal contour of the marking. To prevent the cut piece from damaging the floor, place a stool or cardboard box in this place.

Using a jigsaw, you can get the desired hole much faster with impeccably even and smooth edges. However, you won’t be able to do without a drill, since you need to make the first hole where you can insert the tool’s file. A special stock and built-in ruler will help you complete the job flawlessly and quickly. You just need to take care that the fallen piece does not damage the floor.

It is best to use a milling machine. It is ideal for such work, but only a well-trained specialist who knows how to work with such a tool can use it. After making a hole, before installing the hob, take care of high-quality waterproofing. During operation, steam and water will inevitably destroy the countertop. It is best to use silicone for protection. It is easy to apply, flexible and does not lose its properties with prolonged use.

Steps for securing and connecting equipment when installing a hob.

Simple instructions on the sequence of work performed will help to get a complete understanding of how installation should be carried out so that the equipment can be used long time no additional repair costs.

You need to immediately connect the gas hose, since this will be quite difficult to do later. It is necessary to install a paranitic washer in the union nut. After this, securely screw it to the existing pipe. It can be found at the bottom of the hob. In order for the connection to be as reliable as possible, the paranit should be lubricated with graphite grease or grease.

It is necessary to seal the entire perimeter of the cut hole with sealing tape. It is included in the set of equipment purchased in the store. It is necessary to glue the surface of the tabletop with a continuous layer. When turning, we simply bend the tape without tearing it. The self-adhesive tape will stick tightly in the right place. You only need to gradually remove the protective paper layer. It is best to make a slight overlap at the joint so that there is no gap.

The hob is installed tightly in the cut hole and centered so that the front side looks perfect, without distortion. Then with inside Four special plates are screwed into the corners with self-tapping screws. They provide a tight connection between the equipment and the countertop. You need to tighten the screws as tightly as possible, but be careful not to strip the threads.

Connection to the gas distribution system.

It must be remembered that any work related to the installation of gas equipment is carried out exclusively by representatives of gas services. Otherwise, fines cannot be avoided. Even replacing a regular faucet requires turning off the gas supply in the riser and then testing and obtaining a special permit for use. We take care of all technical and organizational issues and guarantee that all work will be carried out in strict accordance with safety requirements.

Electrical connection.

We install a hob in Moscow or the region in strict accordance with existing technological standards. A moisture-resistant outlet must be used to provide power to the panel. It is mounted in advance on the inside of the headset. It is best to entrust the connection of complex equipment to professionals. This will help avoid accidents and malfunctions.

Installing a hob, the price of which can be quite significant, requires high professionalism and experience. We can give full guarantee the fact that after completion of the work you will not have to think about repairs soon. If the wiring in your home does not seem secure, it is best to install automatic system protection, which will prevent electric shock during a short circuit.

Installing a hob inexpensively by our craftsmen will help you quickly realize your dreams and completely transform your kitchen, making it more modern, comfortable and beautiful. Contact us, we are always happy to help. Call us by phone or leave a request on the website, and we will provide the necessary assistance without delay.

Installing a hob with your own hands is a test of strength for both a beginner and a seasoned master. The hob is an alternative to a large kitchen stove. It performs the same functions, but takes less space. Today we’ll figure out how not to go crazy during the installation process.

How to install the hob yourself? Mandatory installation rules

As a rule, the product is mounted above the oven. A hole of suitable dimensions is made in the countertop and the device is placed on top. When every meter counts, is it possible to install them above the dishwasher or without a countertop?

Types of hobs

Gas

Electric

Combined

The panel can be:

• gas;
• electrical;
• induction;
• combined.

Each of them can be:

• dependent;
• independent.

The first include devices that can only function in conjunction with an oven.

Control is carried out using a panel mounted on the cabinet - very rarely it is located on the hob.

IMPORTANT! Not all hobs and ovens can be used together. Sometimes even products from the same manufacturer are incompatible.

The second category includes hobs that require their own control panel. They are completely independent from oven: This implies complete comfort and placement in any corner of the kitchen.

This allows them to be placed separately, as opposed to dependent ones.

Popular brands

The installation principle from different manufacturers remains the same. Below we list brands that will not let you down.

Model	Description
Electrolux (Electrolux) EHG 96341 FK	Material: glass ceramics. Dimensions: 59 x 52 cm. Rated power: 6.6 kW.
	Material: glass ceramics. Dimensions: 60 x 51 cm. Rated power: 7.2 kW.
	Material: Tempered glass. Dimensions: 10.2 x 73.3 x 50 cm. Rated power: 5.9 kW.
	Material: glass ceramics. Dimensions: 60 x 51 cm. Rated power: 6 kW.
	Material: glass ceramics. Dimensions: 59.5 x 51 cm. Rated power: 6.8 kW.
	Material: glass ceramics. Dimensions: 59 x 52 cm. Rated power: 6.5 kW.
	Material: glass ceramics. Dimensions: 58.3 x 51.3 cm. Rated power: 7.6 kW.
Midea MC-HF602	Material: glass ceramics. Dimensions: 59.0 x 52.0 x 5.5 cm. Rated power: 6 kW.

Correct installation: steps

Electrical panel

Models with electric ignition made of glass ceramics delight with convenience. If the assembly is good, then the product will not require repair for a long time. However, if the surface breaks, detachment will be as simple as possible. It is quite possible to remove the electric cooker yourself and take it for repair.

Let's start embedding. General algorithm:

• Place the electrical panel on the countertop, turn it over and connect according to the diagram. For convenience, manufacturers post instructions on back side products. Connection requires care - in case of an error, control of the burners and heating temperature will be impossible.
• After this, you can turn the panel over and mount it in the hole. Check that the switching on and heating are working correctly. The panel is completely ready for use.

The installation process yourself is not difficult. Especially for those who have ever made repairs or carried out construction works. Detailed algorithm:

1. Determine the dimensions. Before installation, you must read the instructions. It contains a diagram showing the installation dimensions and how to install the panel correctly. This speeds up the process and minimizes possible mistakes during measurements and installation.
2. You can take measurements yourself. To do this, you need to turn the panel back and, using a tape measure, measure required parameters. Be careful: the installation depth is determined by the installation location.
3. Decide on indentations. The instructions indicate the minimum distances from the edges of the tabletop, so we do not recommend making them smaller. This may cause the edge to become damaged and require repair. You can only increase the size.
4. Make markings on the countertop based on the hob measurements. To ensure accurate and simple installation, ensure that the markings are stable. If you draw it with chalk, the lines will be erased, and this will create inconvenience during installation. We recommend gluing strips of paper tape and then applying markings on it.
5. Make a cutout. At this stage you need to drill a hole where the cutout will begin. Using an electric jigsaw, cut out the outline of the top of the tabletop. For an even cut, use a sharp file with fine teeth. Ideally, it is recommended to use a hand router and round the corners using a cutter. In this case, the cuts need to be sanded. After this procedure, sawdust is formed, which is better to immediately collect with a vacuum cleaner.
6. Try on the hob. Check that the cut is correct and try on the panel. This will ensure that you can proceed to the next steps.

Step 1 - Mark on the countertop the place where the hob will be located

Sawing a hole

For installation you will need an electric drill and a jigsaw. If you don’t have them, you’ll have to purchase or rent them, since you can’t do without them.

IMPORTANT! Structure glass ceramic surface quite fragile, so when installing you need to be as careful and attentive as possible, and also objectively assess whether it is worth doing the installation yourself or whether it is better to leave the matter in your hands experienced craftsmen. If you still decide to do everything yourself, then move on.

When buying a hob, it will be convenient to simultaneously place an individual order for the manufacture of furniture. You can simply tell the furniture makers the measurements of the device and they will make the cut themselves. This is the simplest and convenient way installation (then you can go straight to the sealing/sealing point).

Step 2 - Cut a hole in the countertop Step 4 - Place the panel over the hole

Sealing and proper sealing

To extend the service life of the countertop and protect it from premature wear, it is necessary to use silicone sealant or nitro varnish. This treatment prevents the entry of moisture and dirt. Self-adhesive sealant (sealing tape) is also perfect for these purposes.

It is glued on top so that the edges of the built-in model rest on it. Aluminum tape is one of the alternatives for sealing and sealing. This the best option, as it protects the countertop from temperature changes. Thanks to the high-quality seal, the product will last long years without repair.

Step 7 - Connect the hob to the gas pipe. Depending on the type of built-in panel, the connection method changes

Gas panel

The instructions contain information on how the product is attached. Place the panel into the countertop, align it with the edge, then secure it. As a rule, the kit includes special brackets with which fastening is carried out. Then turn on electrical wire into the socket.

All that remains is to connect the gas. First turn off the gas, and then connect the hob to the pipe using a flexible hose. Equip the nuts with paronite gaskets. You can turn on the gas. Make sure that there are no leakage areas at the connection points. To test this, lather them with soap. There is no leakage if the foam does not bubble and vice versa.

If you have a gas analyzer, you can use it.

Hob socket: where to install?

Before installing the equipment, it is better to move the outlet under the countertop. This will ensure maximum ease of use and add aesthetics. appearance- neither the socket nor the plug will be noticeable. It is also necessary to make a hole through which the wire will pass on the way to the electrical network.

IMPORTANT! If you do mark it under the hob and oven, it is recommended to get a hood.

Step 9 - This is what the installed hob looks like

Many years ago kitchen sets We couldn’t imagine the possibility of installing a hob in them. Today this is a common phenomenon, which allows you to save space in the kitchen, and also makes cooking more convenient and comfortable. You can install the hob into the countertop yourself. The main thing is to correctly determine the sequence of actions and follow it. It is very important to correctly determine the dimensions of the future opening.

Modern technologies do not stand still. Today it has become possible to integrate hobs into kitchen units, which has a qualitative effect on the interior of the kitchen and its functionality. The insertion of the hob will not be noticeable for a long time.

The first step is to make a marking on the countertop that will correspond to the dimensions of the hob.

A hole must be drilled next to each side of the niche, the diameter of each should be from 8 to 10 mm. The next step is to cut out a niche and treat its interior with silicone. The tabletop is installed on the lower level of the set. Inner part The panels are secured with double-sided tape or a little plasticine. The table top is coated with silicone.

Step-by-step installation:

1. The tabletop is placed on the lower part of the set. If the walls are uneven, the tabletop will need to be trimmed. And if they pass through it gas pipes, special holes must be made for them. The countertop should be ready to be installed down the kitchen.
2. Inside the box in which the hob will be installed, it is necessary to make markings. To do this, you can simply make pencil marks that will help you make further markings.
3. The tabletop is laid face down, and markings are made on the reverse side for future insertion.
4. In each proposed cut, you need to make small holes so that you can work with a jigsaw.
5. Carefully cut out the niche using a jigsaw.
6. You need to make sure that the tabletop does not sway under its own weight. It is better to carefully support it during the cutting process.

The inside of the cut is treated with silicone. After installing the panel, you can additionally coat it with silicone and outside. This is done in order to create an additional water barrier, since the fasteners may not press against the tabletop enough.

A gas hob must be chosen very responsibly, because it should last for many years. After the choice is made, the panel must be installed so that it is convenient and safe to use. You can install the panel yourself, but you should not do this if you are not confident in your abilities. In any case, you can contact a specialist for help.

At self-installation it's important to prepare everything necessary materials: panel, measuring instruments, pencils, sealant, adjustable wrench, saw, gas winding, steel hose.

All work involving gas is unsafe. It is best to carry out the installation together with a specialist or person who thoroughly knows the entire installation process. One of the most important stages of installation is the choice of hose.

Tips for choosing a hose:

• Check the hose for damage. There should not be a single defect on the hose.
• The hose must be certified. When purchasing, you should ask the seller to present all documents for the goods.
• The hose can be corrugated metal or rubber.

When installing the panel, special attention must be paid to calculating the dimensions. Sometimes you can find a template included with the hob that you need to use in order to properly cut the countertop. It is important to remember that water should not get on the surface of the panel. The gas countertop should be placed at a safe distance from furniture and textiles.

How to properly install a hob into a countertop

A built-in electric stove is a very convenient device to install in the kitchen. It works as efficiently as a stationary stove, but does not take up as much space. You can install such a panel quickly and easily, without the help of specialists. The surface can be combined with an oven, which will make cooking even more convenient.

If this is not the first time the master has carried out independent repairs, then installing the hob will not cause any difficulties.

Before installing the panel, you need to correctly cut the hole in the countertop. To make installation easier, manufacturers indicate required dimensions in the instructions for the device. Preliminary marking greatly simplifies and speeds up the installation process.

Installation steps:

• You need to make markings on the countertop that will correspond to the dimensions of the panel.
• Using an electric jigsaw, you need to make a cutout in the tabletop. To get started, you need to drill a small hole for the jigsaw. The cut will be even if you use a jigsaw file with small teeth.
• The dimensions of the hob must match the cut hole. Sections must be treated with sealant or nitro varnish. Sealing self-adhesive tape can be used for processing.

The electric tabletop is connected based on the diagram. It can be found on the back of the panel. It is important to connect the wires correctly in order to be able to regulate the activation of the burners and their temperature.

What to pay attention to: attaching the hob to the countertop

The hob installation process is simple, but requires careful preliminary preparation. The first step is to choose the right hob, check its passport data, prepare the tools and decide on the installation location. Installation of gas cooking and electrical surface practically no different.

You need to attach the panel to the tabletop, in which you need to make a corresponding cutout.

It should be noted that to install the electrical panel you will also need to install electrical outlet. For a gas panel, you need to take care of the gas communication. The built-in panel must be installed so that the maximum gap between it and the tabletop is 1-2 mm.

What to pay attention to:

• Correctly measure the dimensions of the panel and transfer them to the cutout in the tabletop.
• Cut out the required segment in the tabletop in order to perform the installation correctly.
• Treat the countertop with special materials that will protect it from external negative factors.
• Recess the panel into the cutout.

It is important to remember that the mortise panel should not be forced into the gap. If there is any play, the position of the tabletop must be aligned, focusing on the front edge. Fastening the seal over the entire surface of the tabletop will prevent contamination of the panel.

Hob seal

A sealing gasket must be attached to the hob. If the panel is removed after some time of use, you may notice that the seal will be covered in dirt and grease. The gasket requires replacement from time to time.

If there is a gap between the panel and the countertop, then the plate can be fixed in the plane, but this must be done so that debris does not fall into the vertical gap.

You can buy a special tape, or you can use a glass sealant. The table and cutout can be pre-treated with clear sealant. Remaining sealant must be wiped off or carefully removed with a spatula.

Advantages of sealing tape:

• Reliability;
• Ease of use;
• Environmental friendliness.

Bosch seals are known for their high quality. Simply installing the panel is not enough. It must be protected from moisture, grease and debris. If the panel is installed in a large opening and a gap forms, then tape and treating the gaps with sealant will help save the situation.

Installing a hob into a countertop (video)

The built-in hob is a convenient device that saves space in the kitchen and provides comfortable cooking. The rules for installing the panel are simple, so you can install it yourself. It is possible to embed a panel efficiently only when the dimensions of the panel are measured correctly. After cutting a hole in the countertop, it must be well treated with sealant to protect the panel from water and dirt. All actions must be gradual and coordinated.