How to make a mole spinner correctly. How to make a mole repeller from a plastic bottle? Step-by-step instructions for creating a mole repeller

I surfed the Internet, looked at books and collected some tips on how to get rid of moles.
1. Keep a fresh fish (in the sense of not salted, not smoked) in the sun for a couple of days, let it acquire an odor and put such a gift in a mole’s hole.
2.Across the entire area, at a spread of 1-2 m, insert sticks into the ground, and hang 0.5 liter beer cans on them. You need to hang it so it makes noise.
Sticks 30-40 cm high.
Not a single mole! I didn't believe it at first. Laughed...
Very good way, especially since you need to drain about 2 boxes of beer (depending on the area)!
3.Small selection:

How to deal with moles on the site?

The mole is a very smart animal. They live in families. At one time they spoiled my nerves a lot. Sometimes you can read that they supposedly get rid of moles by placing a small windmill on the site, which creates vibrations in the soil and this scares off the moles. This is wrong. You can read that moles are repelled by a bottle with a chipped bottom buried in the ground at the entrance to a hole; supposedly the wind blows into the neck of the bottle and it works like a police whistle. And that's not true. I found a way that allowed me to catch a mole in the area in 20-40 minutes. It turned out that the mole does not like drafts in his household. I find its underground passage, dig it up and make an exit to the surface of the earth. About a meter from this exit I find a continuation of the same passage and dig a small hole. I set a trap and sprinkle it with earth, that is, I carefully camouflage it. I attach the chain from the trap to the surface, cover the hole with a sheet of plywood and cover it with earth. Thus, I create a draft in his household.. One can only imagine that this literally drives him into a rage. Wherever he is on the site, he immediately rushes to the hole to wall it up. He will definitely have to face the trap. All that remains is after 20-30 minutes to dig up the plywood and pull out the trap and its victim. On my site, in this way, I pulled out 1-3 moles daily for about 10 days. Then they apparently left my site in formation and for 5 years they bypassed it.

My neighbor at the dacha placed about 10 homemade " windmills". He says that the vibration when the propellers rotate, going into the ground, scares away the moles. Height is 1.5-2 m, propellers with a blade of 20-30 cm. At the same time, they scare away the birds and look cool! O. Polyakov.

This is how we do it: a weather vane with a propeller is made, a tin can is put on the axle, pebbles are placed in it, and the whole thing is stuck on a pin (2 meters) into the ground. When the wind blows, the propeller rotates, the pebbles in the tin jar rattle, and this sound is transmitted along the pin to the ground. The moles leave the area; they don’t like this kind of treatment.

To get rid of moles in your garden, simply bury several champagne bottles in different places in your garden, with the neck facing up. The neck should protrude 2-3 cm above the ground. The wind will “howl” in the bottles and the moles will simply leave.

The appearance of moles on a lawn or garden plot does not bode well, even if the animal accidentally damages the roots of plants and does not feed on crops from the garden bed. Trees, shrubs, and vegetable plants that find themselves in the hunting field of the common mole die. Within a few days, nothing remains of the ideal lawns. In addition, they destroy beneficial earthworms and throw layers of infertile soil to the surface.

A good owner cannot stand this, and begins to look for an effective and quick way to get rid of the uninvited guest and his family once and for all.

• Read - and what do they bring more - benefit or harm?

But before organizing the expulsion of the blind pest, it is necessary to at least general outline, get acquainted with its biology. For some, their knowledge of moles ends with the cartoon about Thumbelina. But in real life moles do not count the money themselves, but force the owner of the lawn or garden plot count losses.

Biological characteristics of the pest

The common mole, like the hedgehog, belongs to the order of insectivores. Already from the name of the group it is clear that it cannot feed on potatoes and other underground parts of plants.

Weighing 130 g, the body length reaches 15 cm. It feeds exclusively on insects and for this, at a depth of 10-50 cm, it digs a system of underground passages with its powerful forelimbs. The nest is built at a depth of up to 2 meters. There, in the dug labyrinth, he finds food for himself: earthworms, insect larvae and other arthropods.

On the picture

To compensate for poor eyesight, it has phenomenal hearing and sense of smell. Like all animals, they love silence, so when there is strong sound exposure, they leave the developed territory. People take advantage of this weakness of his. Plastic anti-mole turntables and other homemade repellers made from scrap materials are used.

Plastic pinwheel against moles

The simplest type of repeller. To make it you will need a regular plastic bottle and a metal pipe or thick steel wire, on which the mole spinner is actually put on. Several cuts are made in the bottle, which are folded back to form peculiar pocket blades. The wind causes the blades to spin, which creates noise that resonates into the pipe and goes into the ground.

Several of these tubes can be stuck near mole holes. In windy weather, a mole repeller from plastic bottle its rotation creates an unpleasant vibration, which forces the animal to go in search of a quieter habitat.

This repellent method works on European, Small and Caucasian moles. Moles in the northern regions of Russia most often do not respond to windmills. It is advisable to place several of these windmills at a distance of 10-15 meters from each other.

How to make a pinwheel from beer cans?

Design includes metal pipe and an empty cola or beer can. The top of the can is cut out to fit onto the pipe. The same 3 cuts are made on the jar. For greater noise, it is better to bend the bottom of the can. The choir performed by several noisemakers, the mole will not be able to stand it and will leave his favorite places.

Of course, making a repeller from a plastic bottle is as easy as shelling pears, but not everyone has such a desire. And there can be problems with the wind. In calm, windless weather they will become simple decoration garden plot. And the resonating noise in gusty winds may not please both the craftsmen themselves and their neighbors.

- What methods did we not use when fighting the mole? My husband dug up the entire garden. Moreover, the trenches turned out to be deep, almost as tall as a man. But every time the cunning animal turned out to be smarter than the man. The husband created drafts for him, waited for him to start closing them, and without waiting, he walked away for a minute. He comes, and the hole is closed and there is silence. Then the saga with the bottles began. They surrounded the pest like a wolf with red flags. When a storm warning was announced, such chatter began that the neighbors were the first to break down, and all this time the beast continued to surprise us with fresh mounds. We had to take our anti-mole noisemakers out of the bottles and apologize to the neighbors.

Yana, 36 years old

Alternative methods of getting rid of moles

Except homemade devices to expel pests, there are also industrial options. For example, an ultrasonic repeller. The device looks like an ordinary stick with batteries inside. The device generates ultrasonic waves that are not perceived by the human auditory analyzer, but are annoying to pests.

One of the most successful solutions will be the Tornado-OZV 02 repeller

On the picture

The underground inhabitants begin to panic due to constant mechanical and ultrasonic vibrations.

• The sound source itself is located at a depth of 20 cm, which eliminates the noise effect above the ground.
• Soil is a denser medium, so sound waves propagate better in it and reach a radius of 2 km.
• The device is made of impact-resistant materials that are resistant to dust and moisture. The device operates for 3 months on one set of batteries.
• The price of the Tornado repeller is 1200 rubles.

- Moles took a fancy to our site last summer. The fighting season ended in favor of the miniature animal. A plastic bottle against moles did not help. The onset of spring was met fully armed. We bought a Tornado repeller on the recommendation of a friend who himself suffered from uninvited guests. For a plot of 12 acres we bought 3 pieces. Arranged Bermuda Triangle. After 3 days, the vital activity of the animals ceased. But, judging by the reviews, Tornado does not help everyone. Maybe it's the properties of the soil. We were satisfied and advised everyone who found themselves in our situation to buy it.

Svetlana Mikhailovna, 57 years old

Chemistry against moles

If all of the above remedies do not help, all that remains is to resort to chemicals, but only to scare away the animals. One of them is “Ejector concentrate Doctor Klaus from moles”. Its composition:

• citronella (oil);
• castor oil (31.1%);
• water;
• functional components.

It is best to use the product at the first signs of the presence of pests. The ejector is easy to use. First, attach a hose to it, then turn on the water and treat the area inhabited by insectivores. IN for preventive purposes treatment is carried out every 2-3 weeks.

On the picture

Only the soil should be sprayed, not the plants on it. If a molehill appears where the snow is melting, then the ground is simply watered with the mixture from the ejector for 1 minute. You can also drain the underground passage itself, but first remove the top layer of soil.

The cost of one bottle is about 700 rubles.

In the fight against pests, some people make their own anti-mole pinwheels from plastic bottles, while others use innovative methods. The latter help preserve the harvest without much time and money. To ensure a guaranteed result, you should perform all actions according to the instructions and then victory will be yours.

What you can use to make a mole repeller with your own hands:

• plastic bottles;
• cans;
• electric alarm clocks;
• radio and speakers.

The first three types of repellers do not require any special knowledge or skills. The maximum number of different repellers has been invented from plastic bottles.

Of the industrial mole repellers, ultrasonic ones are the most popular. But according to reviews, not all of them are effective. They speak negatively about Russian-made ultrasonic mole repellers and praise Japanese ones.

By homemade repellers note that moles have little fear of windmills and pinwheels, sometimes making a hole right next to the pin. Ringing alarm clocks or constantly playing modern music to the animals will effectively get rid of moles from the area.

The simplest skewer - DIY noise maker

Keep in mind that the mammal is blind, but its hearing and sense of smell are impeccable. For this reason, it is important that the mole repeller made from a plastic bottle creates noise and vibration. This effect is achieved by blowing wind, which sets the device in motion: the blades rotate, transmitting sound waves downward: a resonance is created inside the ground, scaring off moles. Remember that to protect 6 acres you need to place about 3-4 small wind turbines.

If it is not possible to use several containers, then you can limit yourself to one. To work you will need:

• plastic bottle with a volume of 1.5-2 l;
• metal pin;
• Part water pipe;
• construction or stationery knife.

The turntable manufacturing process is very simple. Do the following:

1. Find the place where the mole passed, install part of the water pipe below the detected passage.
2. Take the pin, place it in the installed pipe, secure the part with a plug or using a metal plate and self-tapping screws (tighten them until the caps fit snugly against the plates).
3. Make a hole at the bottom of the container: its diameter should be larger than that of the pin.
4. On the walls of the container, draw the letters “P” inclined to the side.
5. Cut the blades according to the markings and bend them.
6. Place the plastic propeller you made onto the pin: it should go all the way to the neck, screw on the cap.

The simplest thing is to make a pinwheel that, when rotated by the wind, creates noise. The vibration is transmitted to the ground through the stand and scares away the animals. Birds and reptiles also prefer to stay away from the unknown. It should be taken into account that “motley ribbons” indeed have a “quarrelsome” character and may be offended by an unwelcoming reception.

The issue of mole control is very relevant for summer residents. These seemingly harmless creatures can cause great harm to the garden and the products grown in it. Therefore, many are wondering how to solve this problem. Despite the mass of anti-mole remedies and devices in the city, there is one simple option that everyone can afford.

You don't need to be a skilled craftsman to create this product, and the whole job will take about 20 minutes. Intrigued? Then let's find out how to make a mole repeller from a plastic bottle.

Looking for solutions

There are a lot of requests on the Internet regarding the topic of rodent control, especially moles. Everyone wants to make sure they don't have to deal with this problem anymore. However, not everyone knows how to act in this case. Killing animals is not entirely humane, so poisons and other killing devices will not work. Often gardeners run to the store to ask for advice or buy an effective and at the same time inexpensive product. Others take a simpler path, making a mole repeller with their own hands.

But how can a plastic bottle repel moles? It's simple. All you have to do is upgrade it by constructing unique blades from a bottle that will make it spin. While rotating, the turntable will make noise. The design is quite simple:

1. Plastic bottle.
2. Stick.

That's all you need. The container is placed on a stick or rod, after which it will spin under the influence of the wind. Due to the fact that the rod is buried in the ground, vibration and noise repel moles. You can make many such products for the garden, the cost of which is simply meager. And most importantly, you don't have to spend a lot of time. Let's look at the instructions on how to create this simple miracle of technology.

What you need for work

The advantage of a plastic bottle repeller is that you will need a minimum set of tools and materials. Anyone can work with them, and purchasing them is not a problem at all. You can see this for yourself. Here's a list of everything you'll need:

• plastic bottle;
• steel rod or wooden stick;
• stationery knife or scissors;
• drill with a drill (in some cases this is not required).

That's the whole set. Are you surprised? It’s not worth it, because for all its simplicity, the mechanism works flawlessly. You just need to connect it all into one device.

Note! The device is automatic, but only works from the wind. In calm, windless weather it will simply be useless.

Step-by-step instructions for creating a mole repeller

So, when you have everything you need, you can get started. The bottle can be of any color, shape, volume... This is not so important. Provide yourself comfortable spot for work. It's better to do everything at the table flat surface. Then no problems will arise. The instructions are as follows:

That's all, the device is ready. Now you just need to find the mole's tunnel in order to insert the rod into it. Due to the vibration and sound transmitted from the bottle along the rod into the ground, moles will not approach this place. They are afraid of such aggressive noises. If you have a large garden, then make several structures to prevent moles from appearing in another part of the garden.

Advice! Such a repeller will act not only on moles. Birds and other rodents are also very afraid of such noise. Therefore, you do not have to fear that our smaller brothers will devour your harvest.

Gardens and vegetable gardens are a good help both in terms of food and in terms of relaxation for the soul. But everything that is grown on personal plots, there are many dangers - beetles, larvae, birds, moles. And if they help fight plant diseases or insect pests chemicals, then it is best to scare away birds and moles from the site, rather than destroy them. A primitive design will help with this - a windmill made from a plastic bottle, made with your own hands from scrap materials.

Waste material goes to work

Many, many different kinds useful crafts can be made from so-called waste material. It’s also easy to get useful things for your garden plot and vegetable garden by applying your imagination and skillful hands to seemingly unnecessary things. A lot of various options repellers for birds and moles can be seen in various sources, some of them are quite complex, and some are primitive. It’s worth starting to create with the simplest designs. Plastic bottles, scraps polyethylene pipes, a broken handle from a house mop, a used welding electrode, gift ribbons from already unwrapped gifts, toy bells or drink cans - anything can be used.

Design Basics

It is no coincidence that a device for scaring away birds or moles from a site has a very specific name “windmill”. The main force that makes the structure perform its function is the wind. The wind is blowing - the windmill is working. In order for such a repeller to work, it needs to catch air currents, which means it needs blades. If you set a goal, then making a windmill from plastic bottles with your own hands is quite simple. The most main part- blades, cut from plastic. Moreover, the blades from the bottle will not need to be attached, because they are cut in place and simply bent. The remaining design elements will depend on the purpose of the windmill. Tools you will need for work:

• stationery knife;
• scissors;
• universal glue;
• hard wire;
• beads with a hole for wire;
• self-adhesive film or colored electrical tape.

What are birds afraid of?

Birds provide many benefits by eliminating pests. But when the harvest ripens, they are not averse to eating tasty, sweet fruits, pecking at cherries and spoiling apples, pears and plums. Making a windmill from a plastic bottle with your own hands is quite simple, if you remember that birds are afraid of moving objects. That is why turntables and scarecrows with fluttering sleeves have always helped gardeners and gardeners preserve their harvest.

How to scare away birds

A windmill made from a plastic bottle must be movable to scare away birds. The simplest and a budget option- spinner. It does not require additional costly motors and batteries, because it operates on air movement. But it needs blades to catch the wind. You can make several options for such garden helpers. For example, like this.

Cut an ordinary plastic bottle in the center into four sections that can be bent without separating the parts from the whole.

Then, bending the blades so that they catch the wind, pieces of foil are glued onto them. You can use self-adhesive mirror film. It is also necessary to cut a hole in the bottom that is suitable in diameter. The finished bottle-windmill is put on the remainder plastic pipe or a mop handle. The bottle should rotate freely when the wind blows, but not dangle too much, otherwise rotation will not work. The remainder of the pipe should be long enough for the birds to see the pinwheel.

You can make a windmill from a plastic bottle with your own hands in this version - cut long blades from the base of the bottle, bend them at an angle of 45 0. The turntable diagram is shown below.

Such a windmill is mounted on a rigid base at right angles to the ground. You can secure it in any way - using a nut, if the base is threaded, using a large smooth bead, making a loop on the wire with pliers. There are many options; the master decides which one is more convenient to use. The most important thing is that the turntable rotates freely. Some craftsmen attach several of these devices to one base, decorating them with colored film or painting them acrylic paints. The result is not only functionally useful, but also beautiful thing for a personal plot.

What are moles afraid of?

A windmill made from a plastic bottle to repel moles is a very useful thing, because moles are also pests. They eat earthworms that loosen the soil and spoil the roots and tubers of plants. Sometimes a lot of such underground inhabitants appear on the site. You should get rid of uninvited guests - moles. Moles are practically blind; you can’t scare them with some kind of flicker. But moles have good hearing. It is on this feature that the principle of scaring these animals away from the garden is based. Making a windmill from a plastic bottle with your own hands means saving the harvest, leaving underground inhabitants alive, and not flooding your garden with chemical poison.

How to scare away moles

Moles are afraid of noise, and if you place something on the site that will make noise underground, the moles will leave it, going in search of a quieter habitat. A windmill made from a plastic bottle to repel moles, the diagram of which is proposed below, works just for this outcome. In order for sound to travel well in the ground, it must be amplified using resonance. This can be achieved using a hollow pipe dug into the ground. It will amplify the sound and transmit it across the earth.

The base of the turntable can be taken from the design proposed above - blades are cut out on the body of the bottle, and the windmill itself is placed on a metal base, for example, a used electrode. Sound will be transmitted better through metal than through plastic. Then the electrode, a metal rod, must be placed in the buried pipe so that the sound from the rotation of the windmill is amplified. A do-it-yourself windmill made from a plastic bottle to preserve the harvest is a very simple design.

Pinwheel beauty

Many of those who maintain a garden or vegetable garden try to decorate the area using available materials, the same plastic bottles, for example. What craftsmen can come up with from this waste material. For example, by placing a windmill made of plastic bottles above a flowerbed, you can make it much more interesting. The classic turntable is made of 4 blades according to this scheme.

The blades can be cut out from colorful bottles, then assembled in the center using a bolt and nut or a stapler. You can decorate transparent plastic with self-adhesive film or paint it with acrylic. You can make more than 4 blades. In any case, such a classic windmill made from a plastic bottle, made by yourself, will be an interesting addition to the flower garden.

There are very simple designs of pendant windmills. You can make an interesting decoration from a small plastic bottle - cut the bottle lengthwise in the middle into thin strips 1 centimeter wide. Then connect the upper and lower parts to form a “flashlight”: press the blades in the middle, folding them in half, but at the edges they should be bent at an angle of 45 0. Make a hole in the cork using a hot nail and insert a looped paper clip into it. You can hang a bell or shiny beads on it. The windmill pendant is ready and can be placed on a tree branch.

It’s not difficult to make a windmill from a plastic bottle with your own hands, but it will provide a lot of benefits and beauty.