Installing a glass hob into a countertop. How to properly connect an induction hob

Complex stoves for the kitchen, which simultaneously combine a hob and an oven, are increasingly becoming a thing of the past. Modern housewives are using them less and less for their intended purpose. ovens. They are increasingly turning into storage for pots and pans.

Why overpay for an unnecessary metal cabinet, when you can buy a comfortable and aesthetic hob, and the free space underneath it is perfect for storing dishes and other things. Installation hob Even an inexperienced craftsman can install it into a countertop, because its installation does not require any experience or qualifications.

Types of hobs

So, before you begin such a procedure as installing a hob into a countertop with your own hands (you can see the photo in this article), you should understand the types of these devices. There are the following main types of hobs:

1. Electrical.
2. Induction.
3. Gas.

It is advisable to entrust the installation and installation of the latter option to a professional, since incorrect connection can lead to serious problems. When using gas stoves indoors, special requirements must be observed. When installing electrical panels, it is also important to exercise caution and safety precautions when working with high voltage. It is necessary to provide high-quality electrical power with grounding.

When purchasing a hob, it is important to pay special attention to it since the installation of the hob into the countertop should be done with a small margin around the edges. In addition, you need to decide on the insertion location. Conduct in advance

Tabletop installation

If you purchased glass or stone countertop, it is advisable to entrust its installation to professionals. Since you do not know about all the intricacies of the process, you can damage an expensive item. If you can handle the installation yourself, but with some construction skills.

You will need the following:

• Grouting compound for tiles.
• Tiles for cladding the surface of the countertop.
• Assembly or tile adhesive.
• Tungsten coated tiles.
• Gun with silicone sealant.
• Electric jigsaw.
• Waterproof wood board.
• Set of tools - square, screwdriver, screws.

Replacing a countertop should begin with dismantling the old one. Despite the fact that you will not need the old countertop in the future, you must remove it very carefully to avoid damage to the kitchen unit.

It is very important to adjust the new countertop to the dimensions of your furniture. It is likely that you will need to cut off the excess. In this case, the unprotected edges of the chipboard are exposed. This material absorbs moisture well, so the cuts need to be well treated with sealant. If the table top is mounted with saw cuts to the stove, it is advisable to close them using special end strips.

Required Tools

Before moving on to a process such as installing a hob into a countertop (the photos show what they are like), you need to prepare the following tools:

• Pencil.
• Roulette.
• Jigsaw.
• Drill-driver with a wood drill bit with a diameter of 8-10 mm.
• Sealant.

Preparatory process

First, you should make sure that in the place where the hob will be installed in the countertop, there are accessible ones. The presence of an outlet, a suitable length of the gas supply hose, without squeezing and kinks for a gas stove - these are two fundamental aspects.

If the wiring is old and you are not sure that it is reliable, it is recommended to run an independent cable for the stove directly from the meter.

Installing a hob into a countertop

1. First you need to make a hole in the tabletop. To do this, according to the instructions, an opening is marked. If there are no instructions, then
   The full dimensions are outlined, while on each side you need to retreat approximately 5 mm.
2. Using a drill, a hole is drilled so as not to go beyond the boundary of the contour. Then we continue working with a jigsaw. To reduce chipping, it is recommended to use a file with fine teeth. In addition, you can cover the outline with stationery or masking tape.
3. After the cut is made, you need to paint or seal the cut edges to prevent the tabletop from swelling.
4. Next, the hob is installed in a 28 mm countertop, secured and connected to the network.

The insertion of the panel must be carried out with maximum precision. Otherwise, even a 1 cm error can ruin the countertop, which is one of the most expensive elements of a kitchen set.

Artificial stone countertop

Compared to its chipboard counterparts, the tabletop is made of artificial stone is the most durable. Despite this, the main problem is installing the hob into an artificial stone countertop.

In most cases, an artificial stone countertop is ordered with ready-made holes for a specific hob. But what if the countertop is already installed, but the hob is not yet? In this case, the most reliable and the best option will give the countertop to qualified specialists who, using professional tools, will make the necessary hole.

If you still decide to take a risk, then this work can be produced using the technology described above, but only instead of a jigsaw you will need to take an angle grinder and a diamond-coated disk designed for cutting concrete.

It is important to remember that self-installation of a hob into a countertop must be carefully thought out at all stages of installation. Only in this case will less time be spent on this type of work, and their quality and subsequent result will also significantly improve.

Installing a hob into a countertop: 6 steps

You can install the hob yourself if you first read the instructions Many years ago kitchen sets We couldn’t imagine the possibility of installing a hob in them. Today this is a common phenomenon, which allows you to save space in the kitchen, and also makes cooking more convenient and comfortable. You can install the hob into the countertop yourself. The main thing is to correctly determine the sequence of actions and follow it. It is very important to correctly determine the dimensions of the future opening.

DIY hob installation

Modern technologies do not stand still. Today it has become possible to integrate hobs into kitchen units, which has a qualitative effect on the interior of the kitchen and its functionality. The insertion of the hob will not be noticeable for a long time.

You can read more about the features of electric hobs in the article “3 types of hobs”.

The first step is to make a marking on the countertop that will correspond to the dimensions of the hob.

A hole must be drilled next to each side of the niche, the diameter of each should be from 8 to 10 mm. The next step is to cut out a niche and treat its interior with silicone. The tabletop is installed on the lower level of the set. Inner part The panels are secured with double-sided tape or a little plasticine. The table top is coated with silicone.

In order to properly install the hob, you should follow the step-by-step instructions

Step-by-step installation:

1. The tabletop is placed on the lower part of the set. If the walls are uneven, the tabletop will need to be trimmed. And if they pass through it gas pipes, special holes must be made for them. The countertop should be ready to be installed down the kitchen.
2. Inside the box in which the hob will be installed, it is necessary to make markings. To do this, you can simply make pencil marks that will help you make further markings.
3. The tabletop is laid face down, and markings are made on the reverse side for future insertion.
4. In each proposed cut, you need to make small holes so that you can work with a jigsaw.
5. Carefully cut out the niche using a jigsaw.
6. You need to make sure that the tabletop does not sway under its own weight. It is better to carefully support it during the cutting process.

The inside of the cut is treated with silicone. After installing the panel, you can additionally coat it with silicone and outside. This is done in order to create an additional water barrier, since the fasteners may not be sufficiently pressed against the tabletop.

A gas hob must be chosen very responsibly, because it must last long years. After the choice is made, the panel must be installed so that it is convenient and safe to use. You can install the panel yourself, but you should not do this if you are not confident in your abilities. In any case, you can contact a specialist for help.

At self-installation it's important to prepare everything necessary materials: panel, measuring instruments, pencils, sealant, adjustable wrench, saw, gas winding, steel hose.

All work involving gas is unsafe. It is best to carry out the installation together with a specialist or person who thoroughly knows the entire installation process. One of the most important stages of installation is the choice of hose.

If you need to install a gas hob, it is better to seek help from specialists

Tips for choosing a hose:

• Check the hose for damage. There should not be a single defect on the hose.
• The hose must be certified. When purchasing, you should ask the seller to present all documents for the goods.
• The hose can be corrugated metal or rubber.

When installing the panel, special attention must be paid to calculating the dimensions. Sometimes, included with the hob, you can find a template that needs to be used in order to correctly cut the countertop. It is important to remember that water should not get on the surface of the panel. The gas countertop should be placed at a safe distance from furniture and textiles.

How to properly install a hob into a countertop

A built-in electric stove is a very convenient device to install in the kitchen. It works as efficiently as a stationary stove, but does not take up as much space. You can install such a panel quickly and easily, without the help of specialists. The surface can be combined with an oven, which will make cooking even more convenient.

If this is not the first time the master has carried out independent repairs, then installing the hob will not cause any difficulties.

Before installing the panel, you need to correctly cut the hole in the countertop. To make installation easier, manufacturers indicate required dimensions in the instructions for the device. Preliminary marking greatly simplifies and speeds up the installation process.

Before installing the hob, special markings must be made on the countertop

Installation steps:

• You need to make markings on the countertop that will correspond to the dimensions of the panel.
• Using an electric jigsaw, you need to make a cutout in the tabletop. To get started, you need to drill a small hole for the jigsaw. The cut will be even if you use a jigsaw file with small teeth.
• The dimensions of the hob must match the cut hole. Sections must be treated with sealant or nitro varnish. Sealing self-adhesive tape can be used for processing.

The electric tabletop is connected based on the diagram. It can be found on the back of the panel. It is important to connect the wires correctly in order to be able to regulate the activation of the burners and their temperature.

What to pay attention to: attaching the hob to the countertop

The hob installation process is simple, but requires careful preliminary preparation. The first step is to choose the right hob, check its passport data, prepare the tools and decide on the installation location. Installation of gas cooking and electrical surface practically no different.

You need to attach the panel to the tabletop, in which you need to make a corresponding cutout.

Please note that to install electrical panel you will also need installation electrical outlet. For a gas panel, you need to take care of the gas communication. The built-in panel must be installed so that the maximum gap between it and the tabletop is 1-2 mm.

When installing the hob, special attention will need to be paid to its attachment to the countertop.

What to pay attention to:

• Correctly measure the dimensions of the panel and transfer them to the cutout in the tabletop.
• Cut out the required segment in the tabletop in order to perform the installation correctly.
• Treat the countertop with special materials that will protect it from external negative factors.
• Recess the panel into the cutout.

It is important to remember that the mortise panel should not be forced into the gap. If there is any play, the position of the tabletop must be aligned, focusing on the front edge. Fastening the seal over the entire surface of the tabletop will prevent contamination of the panel.

Hob seal

A sealing gasket must be attached to the hob. If the panel is removed after some time of use, you may notice that the seal will be covered in dirt and grease. The gasket requires replacement from time to time.

If there is a gap between the panel and the countertop, then the plate can be fixed in the plane, but this must be done so that debris does not fall into the vertical gap.

You can buy a special tape, or you can use a glass sealant. The table and cutout can be pre-treated with clear sealant. Remaining sealant must be wiped off or carefully removed with a spatula.

Many people prefer to use sealing tape because it is safe and environmentally friendly

Advantages of sealing tape:

• Reliability;
• Ease of use;
• Environmental friendliness.

Bosch seals are known for their high quality. Just installing the panel is not enough. It must be protected from moisture, grease and debris. If the panel is installed in a large opening and a gap forms, then tape and treating the gaps with sealant will help save the situation.

Installing a hob into a countertop (video)

The built-in hob is a convenient device that saves space in the kitchen and provides comfortable cooking. The rules for installing the panel are simple, so you can install it yourself. It is possible to embed a panel efficiently only when the dimensions of the panel are measured correctly. After cutting a hole in the countertop, it must be well treated with sealant to protect the panel from water and dirt. All actions must be gradual and coordinated.

Similar materials

This step-by-step instruction on how to cut a hole in a countertop made of chipboard or MDF for a hob with your own hands. When you probably need to know how to cut holes in chipboard or mdf countertops if you are installing a sink or hob. This task may seem simple, but we can assure you that there are many nuances that need to be taken into account for a good result.

On the one hand, you must carefully follow the outline of the gas stove using a template or follow the instructions indicated on the product. In most cases there are certain restrictions that you should pay attention to, such as minimum distance from the plate to the back panel or on both sides, to . Use a large L-shaped square to draw a rectangle on your workbench, otherwise the corners will not be at right angles.

To get an accurate hole, you must use a good saw with the appropriate blade. Therefore, the blade must have teeth oriented downward, otherwise it will split the surface. Drill starting holes along the four corners of the rectangle using a drill or (the hole should be wider than the size of the jigsaw blade).

Work plan for installing the hob into the countertop

Materials:

• table top;
• carpenter's pencil;
• insulating tape.

Tools:

1. Protective gloves, safety glasses;
2. Saw or jigsaw;
3. Tape measure, level, square;
4. C-clamps.

• Wear safety glasses when making cuts.
• Choose a blade with fine teeth.

Deadline

• 10 minutes

When installing a gas stove hob or hob, you must cut holes in the countertop.

Tip: Follow the manufacturer's instructions when cutting a hole in your kitchen countertop if you want to prevent potential problems..

How to cut a hole in a countertop for a hob

Marking guide lines

The first step is to determine the outline of the slab. In most cases, it should contain instructions on how to do this, but there is a technique that only provides recommended hole sizes. Place the hob on top of the cabinets. Leave the recommended distance from the back panel to the front edge of the tabletop.

Draw a median on the countertop and mark the cut lines using the manufacturer's instructions.

Marking the countertop for the hole for the stove

As you can see in the picture, you need an L-square, a tape measure, and a carpenter's pencil to get the job done professionally. Make sure the cut lines are parallel and at right angles. In addition, the rectangle must be symmetrical.

Tip: Check that the rectangle under the kitchen cabinet in which the hood will be built is correctly positioned and there is enough space around it (according to the manufacturer's instructions).

Installing spacers under the countertop

To get an accurate result, you should place several spacers under the tabletop. However, the tabletop must be level.

You should leave about 2 inches of space between the cabinets and the countertop, otherwise the saw blade could damage them.

Making initial holes for drilling

Use a drill with a special bit to create starting holes along the corners. It is very important to line up the bits correctly, otherwise you may drill out of line.

Tip: Make sure you use good equipment for drilling with speed control. Set the drill at low speeds and hold the drill with both hands if you want to have good control above her. Repeat the process for each corner of the rectangle.

Passing the laminated layer

In this image you should notice that the drill bit is going through the top layer. Do not apply too much pressure to the drilling equipment, otherwise it may slip out of place.

We remove residues from the process with a vacuum cleaner

Drilling a hole in a countertop with a drill will create a lot of residue, so we recommend that you have someone clean it up as you make the hole.

Tip: Work with great care and attention as it is important to make the holes exactly in the indicated places.

Initial holes for cutting in the tabletop

After drilling the corner pilot holes, you need to make cuts along the guide lines. If you are not experienced in this area, you should cover the cut lines with masking tape. This way you will help prevent the edges from fraying.

Cutting a hole in a tabletop with a jigsaw

To make the cuts, we recommend that you use a jigsaw. Choose a blade with downward-facing teeth. In addition, the blade must have set teeth. If you have not worked with a jigsaw before, we recommend that you secure the tabletop. Make sure the blade follows the cut lines exactly.

Tip: Remove chips that are generated frequently, otherwise they may cover the lines. Set the jigsaw at low speeds.

Finished hole in the countertop for the stove

Last but not least, you need to take care of installing the hob into the countertop yourself. If you followed our tips and read the manufacturer's instructions, the hob should fit into the hole easily. However, if the edges are not completely straight, you can smooth them with silicone or caulk.

Tip: Use sandpaper to smooth the cutting edges.

Installing the hob into the countertop

After this, all you have to do is install the hob into the countertop, connect it and secure it with the screws that should come with it.

Thank you for reading our step by step recommendation How to cut a hole in a countertop and install a hob with your own hands, we recommend that you read other articles. Don't forget to share our projects with your friends using social network widgets.

The first and most important stage of installation work is marking. The external attractiveness of the kitchen unit and the room as a whole depends on the correctness and clarity of the calculations used to cut the hole for the hob.

When making calculations, you should carefully check the result; if you make a mistake by even 1 cm, you can end up with a damaged tabletop, the cost of which is not at all small.

Carrying out marking

The installer's task is to place the panel strictly above the cabinet, taking into account that there is no margin in width.

Marking can be done in only two ways:

• Household option;
• Professional.

For household method the use of special tools is not required, the work is carried out “by eye”. The panel is placed in the center of the tabletop and outlined with a construction pencil. This method is unsafe and there is a risk of damage to the kitchen set.

The second option is suitable for patient collectors; a sufficient amount of time is spent on making calculations. This method minimizes the risk of error.

The calculation process is divided into stages:

• The process begins by moving the internal boundaries of the bedside table above which you want to place the hob. Lines are drawn on the tabletop to form a rectangle;
• Next, the center point of the existing rectangle is calculated. A coordinate system should be drawn from it. A cross is marked, one of its lines should be laid parallel to the front edge of the tabletop, and the second perpendicular to the same base as the first;
• The resulting coordinate system is used to measure the dimensions of the embedded part. Here you need to carefully measure the panel itself, taking into account the small margin, it will allow installation strictly in the center;
• After laying down the dimensions, you need to draw lines, there are four of them. The result is an even rectangular shape, the tabletop is prepared for the correct cutting of the seat.

The calculations have been made, the place for cutting is marked, then we move on to the next stage, which is no less interesting.

How to cut a hole

To carry out work to create a mounting hole for the hob, three types of tools can be used:

• Drill;
• Jigsaw;
• Milling machine.

To create an accurate and correct cut, it is better to use a manual router, but it is unlikely to be found in the tools of an ordinary person who is not involved in assembling furniture. The second option is a jigsaw, even if it is not available, purchasing this tool will not be difficult, its cost is not high.

There is always a drill in the house, but using it to make a hole makes it difficult to install the hob later. The cut edge turns out uneven - this requires additional work to seal the hole. This process takes a sufficient amount of time.

In order to cut a hole with a drill, you will need an 8 mm drill, or 10 mm is possible. The principle of operation is to drill holes at a short distance. Drilling is carried out until they become a single slot.

It is important to understand that work is carried out only on the internal side of the marking. It is required to place a stool under the cut-out piece inside the tabletop itself, this will keep the furniture safe and sound if the cut-out rectangle falls.

Making a hole using a jigsaw is much easier, but you will need a drill. Using it you need to make one hole, which will be the basis of the work. It is also possible to make a cut by hand, but there is a danger of making the cut inaccurately. The first cut can also be made with a jigsaw, but this requires some experience with this tool.

The main thing to remember is to take precautions. For the cut out part of the tabletop, it is necessary to ensure a safe fall - this will eliminate the possibility of damage to the furniture.

After cutting out the hole for the panel, the edges of the slot are treated with silicone. If moisture gets in, the countertop for the hob may become deformed - this will lead to damage. appearance kitchens. A hole cut with a drill is more difficult to process, since torn edges interfere correct application composition, you will need to devote a sufficient amount of time to this process.

Installation and fastening of equipment

Installing a hob into a countertop has its own sequence; for proper independent work, the main thing is to follow all the steps in order:

• The first step is connecting the gas hose to the panel - this will eliminate subsequent installation problems. The hose is equipped with a union nut where the paranitic gasket is attached. Next, the nut is very well secured to the threaded pipe, it is located at the bottom of the hob. To ensure reliable connection, it is advisable to lubricate the paranitic gasket using grease;
• The second stage is winding the sealing tape. It must be fixed taking into account certain requirements. Usually the sealing tape is a component of the hob; it has a self-adhesive base. The protective paper is peeled off from the roll of tape gradually - this will prevent the seal from tangling. It is fixed around the perimeter of the hole on the front side of the cabinet. A prerequisite is the integrity of the seal, so at the corners you should simply turn it and avoid cutting the tape. The two ends fit tightly to each other, eliminating the appearance of a gap;
• Next, the hob is installed in the machined hole. It is imperative to align the equipment so that it looks smooth and beautiful. After centering the device, you can begin mounting it. Let's see what the countertop looks like; under it, in the four corners, you should secure the hob using self-tapping screws and special plates. It should be tightened tightly enough to prevent any gaps from appearing - this will ensure high level safety when using the hob.

Step-by-step process of working with a gas panel

To carry out the process you will need to take construction knife, it is very sharp, so safety precautions must be followed. The gasket, which was previously squeezed out, is very carefully cut off from above.

Next, another part of the gas hose is connected, which goes to the pipe. A mandatory requirement is the installation of a shut-off valve. It is important to understand that the decision to independent work with the replacement of gas taps requires the owner to bear responsibility for working with gas equipment.

Here you must strictly follow safety rules and perform work in accordance with the prescribed requirements. If the gas inspection company finds a violation in self-installation crane, then you will have to pay a fine.

The last stage of the installation work- These are solutions to the issue of power supply. A waterproof socket is required and must be installed before installing the hob. If the equipment is gas, then additional devices not required.

Video: installing a gas hob

Distinctive features of installing an electrical panel

It is important to understand that it is better to entrust the connection of the electrical installation option to professionals. At independent decision this task, there is a danger of harming yourself. Modern panels powered by electricity, they are easy to use and durable.

At correct installation equipment rarely fails. If the panel stops working, then simply disconnect it to carry out repair work. This will allow you to independently deliver the equipment to the workshop, which will save on the visit of a specialist.

The installation of an electrical surface begins with a connection according to the written diagram. It can be found on the panel itself, only with reverse side. When connecting yourself, you need to be careful. Even the slightest mistake can lead to wiring failure throughout the entire room. An incorrect connection may result in the lack of adjustment of the burners.

Some models have a separate wire that should supply electricity directly from the panel. In this case, a socket and plug are not required, and the connection consists of connecting the lead wire to the panel.

Next, the equipment needs to be turned over and installed in the countertop. This process is practically no different from installing a gas model. The main difference is that there is no need to install a gas hose and faucet.

After completing all installation steps, the panel can be checked for errors. If you carefully follow the prescribed diagram, the device should work properly and, most importantly, last for a long time.

Conclusion

Installing a hob yourself is a rather complicated process. But if you follow all safety rules, take into account the nuances and carefully pay attention to the work when connecting the stove to the power supply (gas or electric), then it is quite possible to carry out the installation yourself, saving significantly cash on call from the master. If you have doubts about your own abilities, then for safety reasons it is better to contact a specialist.

The hob allows you not only to prepare any dish, but also to save space. After all, such equipment has smaller dimensions than large and bulky ones. gas stoves. How to install a hob and oven? It's simple. The main thing is to act according to the instructions. Everyone is capable of coping with such tasks. This does not require expensive equipment, but only the availability of certain tools.

What you need

In conclusion

Now you know how to build a hob into a countertop with your own hands. Before starting work, you should evaluate your skills and abilities. If you cannot do this, then you should seek help from professionals. However, it is safe to say that the installation process is not very difficult. Almost anyone can cope with such a task. The main thing is to carefully study the instructions and have everything at hand necessary tools. When performing such work, it is recommended to take into account all the nuances and subtleties of the process.